iDrive® Quad

Applications

	Architectural		Entertainment		Retail		Commercial
	Office		Amenity		Domestic		Signage

Product Description

The iDrive® Quad is a highly efficient (86-88%)* DMX/RDM compliant product, fully approved to CE61347-2-13, which can be deployed as a 1, 2, 3 or 4 channel driver. Two major benefits of this product are its ability to operate in common anode fixture arrangements and the fact that the channels can be bonded, allowing multiple channels to be wired together to deliver a higher forward current output and greater colour variations, including variable CCT. The iDrive® Quad was one of the first high powered LED drivers capable of driving 4 independent LED channels between 350mA and 1000mA and up to 48V DC, approved to CE 61347-2-13.

The iDrive® Quad has been designed to make installation simple and save time by using standard power and DMX connectors with a unique user interface and backlit LCD display menu system to control all functions. Remote management, including set-ups and LED fixture feedback , is done via RDM to enable rapid project installation and monitoring. Further flexibility of the iDrive® Quad’s design is the independence of each of the 4 channels of voltage and current, enabling users to drive LEDs at different currents from one channel to the next, without the loss of efficiency. Each channel can be driven from 100mA to 1000mA in 10mA steps, and up to 48V DC, catering for any type of LED fixture.

The iDrive® Quad was designed with the architectural and entertainment industries in mind, although its flexibility means it is suitable for a whole host of other applications, such as retail, hospitality and leisure. The iDrive® Quad is feature-rich and boasts the same attributes as the other iDrive® drivers in IST’s Generation IV range, such as the iDrive® Force 12 and the rack mounted iDrive® Force 24. The Generation IV range of drivers were the first LED drivers to offer variable voltage, variable forward current and dynamic power sharing control on every channel. Advanced features include:

Features

	Ability to update the software remotely
	Software programmable forward current to suit different LEDs
	Thousands of in-built functions and shows
	Variable Voltage Technology: up to 300m between driver and fixture
	Dynamic Power Control: x2 forward current on RGB scenes
	300,000 hour rated long life solid state capacitors on LED outputs
	Emergency mode for safety applications
	Low ripple current
	Controlled by DMX512, or by using one of the hundreds of pre-programmed settings.

Electrical Specifications

	INPUT
	Input Voltage Range:  100 - 240V AC
	Input Frequency:  50 - 60 Hz
	Consumption:  135 Watts Max
	Power Factor:  >0.92 at full load @ 240VAC
	Efficiency:  >85% at full load
	Connection:  Mains AC loop-in loop-out IEC connector
	Insulation Class:  1
	Standby mode for reduced carbon footprint
	Standby Power:  down to 1W
	Inrush current:  +136.6A / -119.5A
	OUTPUT
	Output Power:  0-48 Watts per channel Max
	Output Current: 100 to 1000mA per channel
	Voltage:  <1 - 48V DC per channel
	LED Connection:  10 - Pin terminal connector or molex 3.0
	Current Resolution: 8-bit & Master Dim
	Channel bonding: Common Anode compatible (to 4A max)
	CONTROL INPUT
	Dimming control:  DMX-512A or RDM as standard
	Connection:  RJ45, loop-in, loop-out
	Dimming Range:  0 - 100%
	DMX Address Range:  001 - 512 via Menu system
	Programs:  See user manual for all pre-sets
	RDM: Full control over functions and sensors.
	MECHANICAL
	Mounting:  Four X 4.5mm holes for fixing
	Construction:  Steel casing for improved thermal dissipation
	ENVIRONMENTAL
	Operating Ambient Temperature:  -10ºC to + 40ºC
	Storage Ambient Temperature:  -20ºC to + 70ºC
	Case Temperature:  + 70ºC
	Relative Humidity:  80%
	Lifetime (failure after 50,000 hours):  5%
	Lifetime (failures after 50,000 hours):  5%
	DIMENSIONS
	210 x 95 x 46 mm

Pioneering LED Driver Technologies.

Integrated System
Technologies Ltd
Suite 5, Birch House
Birch Lane

Business Park
Aldridge, West Midlands
WS9 0NF
England